Product table: Rolamentos autocompensadores de esferas. Width: 7 mm. Bore diameter: 8 mm. Outside diameter: 22 mm. Limiting speed: r/min. Para aplicações de unidade de rolamento de cubo (HBU) de carros de corrida, a SFK fabrica rolamentos de esfera de contato angular (ACBB) de seção fina de. Rolamentos rígidos de esferas com uma carreira para aplicações de altas temperaturas. Cálculo. Modelo em CAD. Visualizar modelo 3D. Localizar um.
|Published (Last):||5 November 2011|
|PDF File Size:||9.15 Mb|
|ePub File Size:||12.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
Basic design bearings Basic design bearings are intended for arrangements where only one bearing is used at each bearing position.
Y-bearing unit data
For the same bore and outside diameter, double row bearings are slightly wider than single row bearings in the 62 and 63 series, but have a rolametos higher load carrying esferras.
They are also available with or without a snap ring groove. When ordering, indicate the number of individual bearings required and not the number of sets. Some sizes in the 70 B series catalogo de rolamentos de esferas skf also available. When arranged in tandem, the load lines are parallel and the radial. As with all vertical shafts, be sure that the bearings are adequately lubricated.
They can accommodate radial loads and axial loads in both directions. Rolamnetos groove ball bearings for special applications include: Contact SKF prior to ordering.
The most catalogo de rolamentos de esferas skf used designs are: Bearings for universal matching Bearings for universal matching are intended to be used in sets. Cages Steel, brass or PEEK cages can be used at the same operating temperatures as the bearing esferss and balls.
Filling slot bearings have a higher radial load carrying capacity than bearings without filling slots, but their axial load carrying capacity is limited. B EC CM B EN 12 10 00 12 01 15 02 17 03 20 04 25 05 30 06 35 07 40 08 45 09 50 10 55 11 60 12 65 13 70 14 75 15 80 16 85 17 90 18 95 19 20 21 22 24 26 28 30 32 34 36 38 40 44 48 50 52 54 56 60 64 SKF Explorer bearings SKF standard bearings 1 For bearings other than those listed, contact SKF.
B EG AP B EG AF Deep groove ball bearings with filling slots catalogo de rolamentos de esferas skf available open or with shields. Because deep groove ball bearings are the most widely used bearing type, they are esferss from SKF in many designs, esfdras and sizes.
The axial load carrying capacity of angular contact ball bearings increases with increasing contact angle. For information about rolamsntos single row deep groove ball bearings, refer to the product information available online at skf.
Other SKF angular contact ball bearings include: When universally matchable bearings are mounted immediately adjacent to each other, there is no need for adjustment. When two bearings are mounted immediately adjacent to each other, a given internal clearance or preload or an even load distribution between the two bearings is obtained without the use of shims or catalogo de rolamentos de esferas skf devices.
The low shoulder enables a akf number of balls to be incorporated in the bearing, giving it a relatively high load carrying capacity.
Y-bearing unit data
Angular contact eolamentos bearings with a larger size than those listed in the product tables are available on request. Double row deep groove ball cataloho are very suitable for bearing arrangements where the load carrying capacity of a single row bearing is inadequate.
If there is too much clearance in the bearing arrangement during operation, the load carrying capacity of the bearings is not fully utilized.
If no reference speed is listed in the product tables, the limiting speed is the permissible speed. Rolaemntos rings and balls SKF angular contact ball bearings undergo a special heat treatment.
Single row deep groove ball bearings are available open or capped with seals or shields.
Rolamentos autocompensadores de esferas SKF Explorer
For additional information, refer to the product information available online at skf. Dkf, it should not be clamped axially, but a small gap should be maintained between the outer ring and the cover flange. Excessive preload produces more friction and higher operating temperatures, leading to a reduction in bearing service life.
When used in this way, the bearing should be mounted with radial clearance in the housing.