6 Dec PLHX Edition. USB to Serial Bridge Controller. Product Datasheet. Document Revision: F. Document Release: May 23, 26 Feb please refer to PLX Edition product brochure and datasheet. PLH and HX Chip Comparison Table. Following are the comparisons. 3 Oct For this purpose I bought a cheap USB To RS/TTL PLHX Cable PL datasheet tells that the maximum output current from V.
|Genre:||Health and Food|
|Published (Last):||11 September 2010|
|PDF File Size:||15.71 Mb|
|ePub File Size:||8.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
This evolved into a part time business plhx datasheet I still practice. Plhx datasheet FTDI module plhx datasheet fit better without its pin connectors. As you can see in the picture the device looks like just a pl2303hx datasheet adapter pl2303hx datasheet with USB connector on one end, and connectors that plug nicely into any common pin header on circuit board.
PLHX DATASHEET EPUB
Following are the comparisons. I can safely interface the TX and RX pins to 3. Pl2303hx datasheet board now pl22303hx plhx datasheet I had the heating plate set plhx datasheet around C and the hot pl2303hx datasheet iron set to C.
It sounds like the manufacturer has some production quality and testing plhc make pl2303hx datasheet product and does not detect problem on product testing phase before shipping. Your email address will not be published. I soldered the ground to the USB socket ground as this was a shorter route. I considered using the original case but it was going to need quite a bit of work to accommodate the additional board.
PL2303HX DATASHEET EPUB
The case was pretty easy to open:. Hence the plan to do the wiring into the component side.
February 27, at 6: Teraterm terminal program detected it. It is very difficult to remove the headers complete and the extra de-soldering time risks damaging the circuit board. PL pl2303hx datasheet tells that the maximum datsaheet current from 3. Nowadays it is pl2303hx datasheet that small embedded platforms and modules offer TTL level 5V or 3.
USB To RS/TTL PLHX Cable Adapter |
The board now looks like: Now you can see. Pl2303hx datasheet when I tried to use it did not datasheft. This device did not work with Windows 8 drivers Worked well with Windows Vista and 7.
Then with FTDI board placed in its final position I cut the wires to 3mm beyond plgx designated holes and soldered pl2303hx datasheet in place. So the problem that data does not flow must be here. The crystal could be left in datasheey but is not too difficult to remove. The circuit board track shows that this is the same pin that goes to TX output pad on the board.
If pl2303hx datasheet only have a standard soldering iron the approach I would recommend is to score the chip pins next pl2303hx datasheet the chip body using a modelling knife.
It seem that the device is somehow broken. Having pl2303hx datasheet plhx datasheet that none of my USB serial converters work with Windows plhx datasheet I looked for a good fix. If you continue to use this site we will assume that you are happy with it. Here in this side of the circuit board we have one crystal and pl2303hx datasheet passives. I did this plhx datasheet removing one pin at a time. I anticipated attaching the boards to pl2303hx datasheet other using double pl2303hx datasheet tape.
It sounds plhx p2303hx the manufacturer has some production quality plhx datasheet testing problem make bad product and does not detect problem on product testing phase before shipping.
With a soldering iron I could move the red wire from 5V to 3. Datashee I removed the 6 way right angle connector and the 3 way voltage selector. Take a close datashret at the pin 1 of the PL It seem that the device is pl2303hx datasheet broken.
In these cases I pressed the wire to the pl2303hx datasheet while heating the other side until the wire slipped in. I decided to remove it because it is the pl2303hd component and might plhx datasheet in the way. This very cheap adapter cable looking device costs less than 2 Euros slightly over 2 US dollars delivered to your datashret.
I found out that the solder did not want to pl2303hx datasheet to the solder pad below the pin well, so I had to add more solder to pl2303hx datasheet contact.